background image
Jims M-8 Valve Spring Compressor 
for diassembly and assembly of 
the multiple smaller valves on M-8 
Conical valve spring adapter only to be 
used with VT #16-1771 Valve Spring Com-
pressor Tool.
VT No. 16-1189
Jims Main Bearing Remover and 
for 2017-up M-8 Big Twins 
removes left or right main bearing without 
damaging the case. Also provides correct 
alignment and depth during assembly. Fits 
2017-up FLT, 2018-up FLST, FXST.
VT No. 16-1182
Jims M-8 Left Main Seal Removal Tool. The 
Milwaukee Eight has a new crankshaft oil seal 
that is difficult to remove without potentially dam-
aging the crankcase bore. The tool is designed 
to do the job with no chance of damage to the 
case. Simply insert the removal fingers over the 
engine output shaft, and then slide the lock collar 
over the fingers. Once assembled, you can eas-
ily remove the seal square to the core by simply 
turning the wrench. Use on the new Milwaukee 
Eight engine, 2017-up. 
VT No. 16-1200
Jims M-8 Cam Bearing Remover and 
Installer Tool 
is required 2017-up FLT 
and 2018-up FXST, FLST M-8 models. 
This tool holds tighter tolerances which 
allows for a more precise installation depth. 
*NOTE: This remover uses the "Jims 
Style" remover collet as well as "Jims" fine 
threaded installation driver.
VT No. 16-1185
Jims M-8 Cylinder Hold Down Nuts Kit 
keep the cylinders in place when the heads 
are removed from the engine. Useful when 
installing the second cylinder over the 
piston and rings after the first cylinder has 
been installed. Fits 2017-up FLT, 2018-up 
VT No. 16-1186
Jims M-8 Wrist Pin Remover Adapter quickly 
and easily removes the wrist pins in M-8 en-
gines. Save space your tool box, use with Jims 
TC-88 wrist pin remover tool. Fits 2017-up FLT, 
2018-up FLST, FXST.
VT No. 16-1187
Jims M-8 Cylinder Head Holder is two sided, 
one side threaded for Twin Cam heads, and the 
other threaded for M-8 models.
VT No. 16-1188
Jims M-8 Countershaft 1st Scissor Gear 
Alignment Tool 
ensures that the scissor 
gear teeth mesh correctly with the main-
shaft 1st fear. For M-8 models. 
*Note: it is 
installed before the scissor gear is removed 
to maintain alignment of the gear halves 
under spring pressure.
VT No. 16-1190
Jims FLT Inner Primary Shifter Shaft Bushing 
 easily removes both worn bushings and 
quickly installs the new bushings to the proper 
location at the same time, without removing the 
inner primary.
VT No. 16-1193
Jims Swingarm Bearing Installer Tool.
VT No. 16-1194
Jims Axle Installation Guide for 2008-up mod-
els with either a 1" or 25 mm hollow axle. Aids in 
aligning wheel with swingarm and brake caliper 
during assembly.
VT No. 16-1195
Jims M-8 Shifter Mechanism Sleeve Remover 
and Installer i
s for removing and installing the 
shifter mechanism sleeve in M8 transmissions. 
The sleeve can be removed and installed cor-
rectly without disassembling the transmission.
VT No. 16-1191
Jims Fork Cap Installation Tool
VT No. 16-1198
Jims M-8 Cylinder Torque Plate Kit
VT No. 16-1201
Jims Steering Head Race Installer Tool
VT No. 16-1196
M-8 Tool