|
|
 |
|
|
Cylinder |
|
|
|
|
 |
|
|
|
|
 |
|
|
|
|
|
|
|
 |
|
|
 |
|
|
|
|
 |
|
|
|
|
|
|
| Jims Evo Case Cylinder Spigot Bore
Tool allows boring of cylinder spigot hole,
up to 3.8125” by utilizing the stock cylinder
stud holes. Use on all 1984-99 style Evo
crankcases. |
| VT No. |
Price |
16-1409 |
$869.00 |
|
|
|
|
|
|
| Cylinder Head and Crankcase Boring
Fixture designed to simplify and reduce
the time required to prepare the
crankcase and cylinder heads for big bore
kit installations. The boring plate is made
of cast iron and is precision ground and
machined with Pan and Shovel head bolt
patterns in one end. The other end has
been finished with the cylinder base patterns
of Knuckles, Pans, Shovels and V2
Sportsters and Big Twins. When adapted
to boring bar it is possible to bolt the
crankcases or heads to the plate and perform
the boring modifications necessary
for 3 5/8” bore cylinders. V2s require use
of spacers because of the extreme length
of the cylinder and head spacer, part VT
No. 16-1868. Big Twin V2’s with male style
studs require on spacer VT No. 16-1868
and one spacer VT No. 16-1869.
Note: Big Twins V2’s with female type
studs must be changed to the male type
of studs, when installing a sidewider. |
| VT No. |
Price |
Item |
16-1867 |
$405.00 |
Boring Plate with screws |
16-1868 |
$75.00 |
3 11/16 Spacer |
16-1869 |
$59.00 |
7/8 Spacer |
|
|
|
|
|
|
| S&S Evo Cylinder Torque Plate Kit simulates
stress conditions when boring and
honing Evo Cylinders. Machined from
chromemoly steel, fits all Big Twin 1340 and
Sportster 883-1100-1200 cylinder, and 35/8
S&S cylinder. |
| VT No. |
Price |
16-0928 |
$424.00 |
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
 |
|
|
|
|
|
|
|
| Ring-O-Matic Ring Compressor has pliers
which incorporate precision locking
action for exact holding and quick release.
Includes pliers and 6 bands, size range
from 2 7/8” thru 4 3/8”. Complete kit. |
| VT No. |
Price |
16-0622 |
$105.00 |
|
|
|
|
|
|
|
| Cylinder Torque Plate Kit by Delkron tool
fits Shovel and Evo cylinder up to 4” bore to
simulate stress condition when boring and
honing cylinders. Order studs for XL separately.
|
| VT No. |
Price |
Item |
16-0929 |
$279.00 |
Delkron BT |
16-0940 |
$44.00 |
Delkron, Studs for Ev XL |
|
|
|
 |
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
 |
|
|
|
|
VT No.
16-0911
Tube
Installed |
|
|
 |
|
|
|
|
|
| Cylinder Hold Down Nuts are used to
hold down cylinders during service. Allows
motor to be turned over with heads off.
Use on all Twin Cam and Evo Twins. Set
of 4. |
| VT No. |
Price |
16-0446 |
$59.00 |
|
|
|
|
|
|
|
|
|
| Evolution Cylinder Oil Passage Drain
Tubes for stock bore size cylinders only.
Each kit is supplied with tap, hex wrench
two drain tubes and instructions. |
| VT No. |
Price |
Item |
16-0911 |
$64.00 |
Kit |
16-0912 |
$45.00 |
Pair Replacement Tubes only |
|
|
|
|
|
|
|
|
| Trock Cylinder Base Lapping Plate is
constructed of cast iron and has 2 sides to
lap warped Stock Evo or 3 5/8” Cylinder
base, supplied with compound. |
| VT No. |
Price |
Item |
16-0713 |
$100.00 |
Plate |
41-8003 |
$10.00 |
Compound |
|
|
 |
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
| Cylinder Wall Flex Hone features silicone
carbide globules which allow the
deglazing of cylinders 3” to 4 1/4” when
powered by a 3/8” or larger drill,180 Grit. |
| VT No. |
Price |
Bore |
16-0574 |
$102.00 |
4 1/4” |
16-0576 |
$96.00 |
4” |
16-0575 |
$90.00 |
3 5/8” |
16-0616 |
$62.00 |
3 7/16” - 3 1/2” |
16-0618 |
$57.00 |
3 3/16” |
|
|
|
|
|
|
|
| Jims Piston Pin Support Plate provides
a non-marring flat support to push the bottom
of the piston against as rings and
cylinder are installed over piston. Use on
all 1936-up Twins. |
| VT No. |
Price |
16-1164 |
$76.00 |
|
|
|
|
|
|
| 1260 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
