|
 |
|
Jims 2006-up Dyna/2007-up FXST-FLTTools |
|
|
|
 |
|
 |
Jims Right Side Drive Transmission Trap Door
Puller Tool. |
|
|
Removes access
door on all right side
drive transmissions
| VT No |
16-1356 |
Price |
$166.00 |
|
 |
|
Jims Main Drive
Gear Installer
Tool. This tool will
hold the main drive
gear square to its
bearing bore for
proper main drive
gear installation. Use on 2006-up Dyna and 2007-up FXSTFLT
models.
| VT No |
16-1350 |
Price |
$276.00 |
|
|
|
 |
Jims Primary Locking
Tool use this tool to
lock clutch hub sprocket
to the front engine
sprocket. Allows
removal or torquing of
clutch hub and engine
nuts. Use on all 2006-up Dyna and 2007-up models.
| VT No |
16-1357 |
Price |
$51.00 |
|
|
|
 |
Jims Inner Cam Bearing
Remover Tool allows removal
of needle bearing and will also
keep needles from falling into
engine. Use on 2006-up Dyna
and 2007-up FXST-FLT models.
| VT No |
16-1351 |
Price |
$225.00 |
|
|
 |
Jims
Transmission
Door Removal
Tool use this tool
to pull complete
door with gears
and shafts from
transmission. Use on 2006-up Dyna and 2007-up FXST-FLT
models.
| VT No |
16-1358 |
Price |
$142.00 |
|
|
 |
Jims Cam Locking Tool
allows removal and torquing of
cam sprocket bolts by locking
camshaft and crankshaft
sprockets. Use on 2006-up
Dyna and 2007-up FXST-FLT
models.
| VT No |
16-1352 |
Price |
$74.00 |
|
|
|
|
 |
|
Jims Transmission Main Drive
Gear Nut Wrench Tool. Use to
remove the 2 1/4” hex nut from
main drive gear which secures
the rear drive trans pulley. Use
with 1/2” drive ratchet. Use on all 2006-up Dyna and 2007-up
FXST-FLT models.
| VT No |
16-1359 |
Price |
$153.00 |
|
|
 |
Jims Main Drive Gear Bearing and Seal
Installer. This tool will hold bearings and
seal square to its bore for proper installation
and will also allow both to be installed
to proper depth. Use on all 2006-up Dyna
and 2007-up FXST-FLT models.
| VT No |
16-1353 |
Price |
$101.00 |
|
|
|
|
 |
Jims Inner Cam Bearing
Installer Tool. Use this tool
to press in the two inner cam
bearings without damage to
bearings. Installs bearing to
proper depth in case. Use on
2006-up Dyna and 2007-up
FXST-FLT models.
| VT No |
16-1360 |
Price |
$183.00 |
|
|
|
 |
Jims Case Splitter. Use this tool
to break the case sealant by
pushing apart both case halves.
Use on 2006-up Dyna and 2007-
up FXST-FLT models.
| VT No |
16-1354 |
Price |
$249.00 |
|
|
|
|
|
|
 |
Jims Main Bearing Installer Tool. Allows proper installation
of transmission case main bearing by holding bearing square
to its bore. Use on 2006-up Dyna and 2007-up FXST-FLT
models.
| VT No |
16-1355 |
Price |
$173.00 |
|
|
| 1255 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
